Did I get ripped off? - BasilMarket Forum

thread starter OSparkX Jul 02 2009 + PM | QUOTE | PERMALINK | REPORT

I bought lvl 50 thief pants for 1 mill. Did I get ripped off?

spheal789 07/02/09 + PM | QUOTE | PERMALINK | REPORT

Yes you did... Unless they were scrolled?

TLNinjah 07/02/09 + PM | QUOTE | PERMALINK | REPORT

If they were scrolled well... no. Otherwise, hell yes.

Daniish Jul 02 2009 + PM | QUOTE | PERMALINK | REPORT

from FM is worthy. From a random guy jumping in fm entrance you can get it easily for about 200k - 350k

aznarcher904 07/02/09 + PM | QUOTE | PERMALINK | REPORT

depends on how good they were. If they were avg... then you could've gotten avg ones for a lower price.

OSparkX 07/02/09 + PM | QUOTE | PERMALINK | REPORT

It was a random guy talking Spanish to his other Spanish friend, and I just asked to buy his pants. I was desparate. A lvl 50 with a lvl 50 shirt but with no pants.

iAMcooovaba 07/02/09 + PM | QUOTE | PERMALINK | REPORT

haha ohh yeh

Weeeddd 07/02/09 + PM | QUOTE | PERMALINK | REPORT

@twopostsabove whatBBQ?

Daniish 07/02/09 + PM | QUOTE | PERMALINK | REPORT

You got ripped off

frozenfury 07/02/09 + PM | QUOTE | PERMALINK | REPORT

napkins said: "Power hacksaw machines having a mechanical feed can usually be regulated to feed the saw downward from 0.001 to 0.025 inch per stroke, depending upon the type and size of the material to be cut. On these machines, a device to stop the feed when hard spots are encountered is usually incorporated into the design. The feed of machines having gravity feed is regulated by the weight of the saw frame and any additional weights or springs that might be connected or attached to the frame to increase or decrease the downward force of the hacksaw blade. Maximum and minimum blade pressures obtainable are determined by the manufacturer of the hacksawing machine, and are specified as relatively light or heavy. The following general rules apply for selecting proper feeds for hacksawing machines: * The feed should be very light when starting a cut and can be increased after the cut is well started. * Hard materials require a lighter feed than soft materials; reduce the feed when welds or hard spots in materials are encountered. * Wide material requires a heavier feed than narrow material because the pressure is distributed over a larger surface. * Sharp hacksaw blades will cut well with lighter feeds. Heavier feeds are necessary for cutting with dull blades. BANDSAWING The cutting speed of the bandsaw machine is the speed of the bands blade as it passes the table measured in feet per minute. The feed of the horizontal band saw machines downward pressure applied to the material being cut by the bands blade. The feed of vertical bandsawing machines is the pressure applied to the bands blade by the material being cut. Bandsawing Speeds Proper bandsaw speeds are important in conserving bands blades. Too great a speed for the material being cut will cause abnormally rapid blade wear, while too slow a speed will result in inefficient production. The chart of recommended speeds (Figure 6-17) are guidelines only. It shows the speeds for a given type of machine. The cutting speed always depends on the type of machine you are using and the manufactures' recommendations. All bandsawing machines have several cutting speeds. Since the diameter of the drive wheel of the bandsaw machine establishes a fixed ratio between the motor or transmission speed in RPM to the blade speed in FPM, it is not necessary to convert RPM into FPM as with most other machine tools. The speeds are identified in FPM on the sawing machine speed selector controls. Some machines have a speed indicator so a careful check of sawing speeds may be made when the machine is operating with or without a load. In general the following principles apply to speeds of bandsaw blades: * The harder the material, the slower the speed; conversely, the softer the material, the faster the speed. * The faster the speed, the finer the finish produced on the cut surface. This principle applies to light feeds in conjunction with fast feeds. Horizontal Bandsawing Machine Feeds Feed of horizontal bandsaw machin

OSparkX 07/02/09 + PM | QUOTE | PERMALINK | REPORT

frozenfury said: " And this has to do with his question how? ._." It just does.